 |
|
|
|
  |
|
Bus Analyzer
3U CompactPCI system diagnostics tool including board and bus testing.
3U
OSS-CPCI-3U-BA
Product Features
- CompactPCI system diagnostics tool including board
and bus testing
- Exercises bus memory, I/O, and Config space
- Captures with 66Mhz, 64 bit CPCI analysis
- 16 event counters, 8MB target memory
- Plug in cPCI board under test
- RS232 and USB interface
- 64/32 bit; 16MB-128K depth
|
The OSS-BA is the ultimate CompactPCI analysis tool. All aspects
of CompactPCI system diagnostics are provided including board and
bus testing. A CompactPCI board under test can be plugged into
the cPCI test connector and analyzed independently or with system
bus traffic. A long list of features include bus tracing, exerciser,
target memory, performance analysis and optional high speed timing.
Capture: 66Mhz,
64 bit CPCI analysis, 133Mhz sampling, 4, 8, or 16MB trace memory,
8 event recognizers, 16 trigger levels
Exerciser: Memory, I/O, config
space, 64/32 bit transfers, DMA controllers, Burst and single cycles,
Memory testing, User defined pattern generation
Target: 8MB target
memory, Zero wait state, Burst and single cycle, Programmable address
Performance
Analysis: Bus Usage Histograms, User defined histograms
Bus bandwidth,
Transfer rates, 16 event counters
cPCI Board Test Interface: Plug
in cPCI board under test, Secondary cPCI bus interface, Perform
independent board test, Bridge to cPCI bus,cPCI bus address translation.
Specifications
| cPCI Compliance |
PCI 2.1 Compliant |
| Bus Size |
64 or 32 bit |
| Bus Signal Levels |
5V or 3.3V |
| |
|
| Trace Specifications |
|
| Trace Memory |
16MB (128K by 128 bits) part number OSS-BA |
| |
32MB (256K by 128 bits) part number OSS-BA-2 |
| |
64MB (512K by 128 bits) part number OSS-BA-3 |
| Sampling Rates |
133Mhz max. |
| |
500Mhz max (optional High Speed Module) |
| Sampling modes |
System Clock |
| |
System Clock w/ Address/Data |
| |
System Clock w/ Transfers |
| |
On board precision Oscillator (7.5ns to 15ns) |
| Sampled Signals |
AD[63:0], C/BE [7:0], FRAME, DEVSEL, TRDY, IRDY, PAR, REQ,
GNT, RST, LOCK, CLK, INTA, INTB, INTC, INTD, |PAR64, PERR,
SERR, REQ64, ACK64, TDO, TDI, TCK, TMS, TRST, SDONE, |SBO.EXT
[7:0] |
| External Inputs |
8 Front Panel Trace/Trigger inputs |
| External Output |
1 Programmable trigger output |
| Triggers |
8 match conditions each specifying 100 cPCI
signals and 8 external triggers and anomaly |
| Trigger Types |
16 Level Sequencer |
| |
Logical Combination |
| |
Single Condition |
| Trigger Positions |
0%, 25%, 50%, 75%, 100% |
| Occur Counters |
16 hardware counters – 20 bits |
| Event Counters |
16 hardware counters – 20 bits |
| Time Tag |
7.5ns to 60 sec. |
| |
|
| Exerciser Specifications |
|
| Initiator Bandwidth |
528MB/s burst rate |
| Initiator Bus Width |
64 or 32 bit |
| Initiator Transfers |
Memory |
| |
I/O |
| |
Configuration |
| |
|
| Target Specifications |
|
| Target Memory |
OSS-BA 8MB |
| |
OSS-BA-2 16MB |
| |
OSS-BA-3 32MB |
| Target Bandwidth |
528MB/s burst rate |
| Target Bus Width |
64 or 32 bit |
| |
|
| Front panel Interfaces |
|
| RS232 Port |
DB9 |
| |
110 to 115 Baud (cable included) |
| USB Port |
Series B connector, 12MB/s (cable included) |
| Indicators |
GO LED |
| |
USER LED |
| Pushbutton |
Reset analyzer or system |
| External Power |
2 conductor front panel (cable included) |
| Trigger |
10 pin socket |
| |
(8 in, 1 out, 1 ground) (cable included) |
| Fuses |
Main power and external power |
| Power Requirements |
Operating 5V at 3Amps max |
| |
Standby 5V at 1Amp max |
 |
|
|
|
|
 |
|
 |
 |
|
 |
|
