| System Processor |
Socket or soldered low power Celeron
M processor in 479-pin |
| |
FC-PGA and FC-BGA package with 400 MHz processor
system bus. |
| Memory |
333 MHz memory speed, Intel 82855GME GMCH |
| |
256MByte, 512MByte or 1GByte PC333 DDR-SDRAM
with or without ECC via standard 200-pin SODIMM socket |
| Within 8HP |
Onboard 2.5" HDD mounting |
| |
CompactFlash socket type II (Flash or Microdrive
HDD) |
| |
1MB Firmware Hub for BIOS |
| |
8KByte EEPROM for CMOS data storing (no battery
operation) |
| Connectivity |
|
| 4HP board |
Ethernet: Intel 82801DB ICH4 10/100Base-TX
Ethernet controller (based on 82559; front or rear IO) |
| |
VGA: Intel82855GME GMCH internal VGA controller
providing 2048x1536x8bit/60Hz resolution, max. shared memory
64MB, analog CRT and DVI signals are connected to the 29-pin
DVI-I connector (front IO). Dual head applications possible. |
| |
Optional for customization an onboard LVDS
interface is available. |
| USB |
3x USB2.0 channels up to 480Mbit/s from ICH4,
1x as front IO, 2x as rear IO |
| PS/2 |
PS/2 for keyboard and mouse legacy support |
| IDE |
Two EIDE interfaces, UltraDMA/100. |
| Primary port |
UltraDMA/100 44-pin, 2mm connector onboard. |
| Secondary port |
UltraDMA/100 40-pin, 2.54mm connector onboard |
| COM |
2x as rear IO |
| Reset |
two-pin onboard connector |
| 8HP additions |
COM: one of the rear IO ports alternatively
available on front IO |
| |
IDE: Primary port available via mezzanine
module for onboard 2.5" EIDE |
| |
Flash Disk or HDD mounting option and in addition
CompactFlash socket. |
| Front Panel Functions |
|
| 4HP |
Ethernet: One RJ-45 with integrated LEDs
(ACT, SPEED) |
| |
DVI: 29-pin D-Sub DVI-I connector (optionally
for customization a VGA-CRT 15-pin D-Sub SVGA connector is
available instead of DVI) |
| USB |
One 4-pin connector |
| |
LED·s: ACT, SPEED (LAN), Thermal, Watchdog
or both general purpose |PS/2: Keyboard/Mouse |
| |
8HP additions to 4HP: |
| COM1 |
One 9-pin D-Sub (RS232) |
| |
CompactFlash: Opening for CompactFlash, CompactFlash
socket with integrated ejector (not hot swappable) |
| |
Reset: Reset button, guarded |
| |
LED: IDE-HDD activity |
| Exceptional Performance: |
Rear I/O via J2 |
| |
The Rear I/O versions support: |
| |
Two USB 2.0 ports |
| |
One Fast Ethernet port without LED |
| |
Two COM ports (TTL level) |
| |
Primary IDE port |
| |
CRT VGA port |
| |
Two fan control inputs |
| |
One general purpose output |
| |
Input for external backup battery |
| |
PS/2 for Keyboard and mouse |
| CompactPCI Bus Interface |
PICMG 2.0 Rev. 3.0 compatible, 32-bit/33MHz
System master:|5V VI/O (3.3V on request), 7 Req/Gnt & clock
lines |
| |
Version with rear I/O on J2 PICMG 2.0 |
| Supervisory Functions, Clock/Calendar |
Watchdog, software configurable, 125 msec
to 256 sec. in 12 steps, generates |
| |
IRQ, NMI or hardware reset, two stage configuration
for NMI and Reset |
| |
Hardware monitor LM87 for thermal control,
fan-sense and all important onboard voltages |
| |
ICH4 internal RTC (MC146818 compatible), RTC
and 256 Byte CMOS RAM with backup, battery replaceable |
| Hot Swap |
Support for all signals to allow peripheral
boards to be hot swapped. The individual clocks for each
slot and access to the backplane ENUM# signal comply with
the PICMG 2.1 Hot-Swap specification. |
| Compliancy |
CompactPCI Core Specification PICMG 2.0 Rev.
3.0 |
| |
CompactPCI Hot Swap Specification PICMG 2.1
R2.0 |
| |
Designed to meet or exceed:- Safety: UL 1950,
UL 94, CSA 22.2 No 950, EN 60950, IEC 950 |
| |
EMI/EMC: EN 55022 / EN 55024, EN 50081-1 /
EN 6100-6-2" |
| General |
Dimensions: 100mm x 160mm |
| |
Weight: 320g / 4HP, 560g / 8HP |
| |
MTBF: >120,000 h |
| Software Support |
Phoenix BIOS with QuickBoot, QuietBoot, BootBlock,
MultiBoot III, PC Health Monitoring, Serial port remote control
with CMOS setup access, BIOS parameters saved in EEPROM,
diskless, keyboardless, videoless operation. LAN boot support. |
| |
USB Floppy boot, USB memory stick boot. Plug&Play
capability. |
| |
Board identification number accessible via
EEPROM |
| |
Support for Windows 2000, XP Pro, XP Embedded,
Linux, VxWorks, other OS’s may be possible, please
contact us for information). |
| Power Consumption |
+5V/ 11W, +3.3V/ 9W, typ. 20W at 1.3GHz (10W
at 600MHz) |
| |
+5V/20W, +3.3V/10W, max. 30W at 1.3GHz (14W
at 600MHz) |
| |
+12V / -12V not used |
| Environmental |
Operating temp.: 0C to +60C standard |
| |
Storage temp.: -55C to +85C |
| |
Climatic Humidity: non condensing 93% at 40
C (acc. to IEC 60068-2-78) |
| |
Altitude: 15.240 meter (50,000 ft.) |
