| Central Processor |
1.8 GHz Intel® Pentium® M
processor 745:-400 MHz Front Side Bus (FSB) |
| |
Common processor features are:-uses µFC-PGA
478 (micro Flip-Chip Pin Grid Array) package 64 Kbytes of
primary (L1) on-die cache 2 Mbytes of secondary (L2) on-die
cache no CPU fan |
| DRAM |
supports up to 2 Gbytes DDR ECC SDRAM via
two SODIMM sockets error correction up to 4-bits accessible
from processor or CompactPCI bus |
| Hard Disk Interfaces |
EIDE interface:-supports up to Ultra-DMA 100
for high performance drives |
| |
two channels (primary and secondary) |
| |
secondary channel can be used for on-board
2.5 inch hard disk drive (within a single slot); or, support
for 1 or 2 CompactFlash modules or Hitachi GST Microdrive™ Type
II drives |
| |
primary channel is accessible via Transition
Module |
| Ethernet Interface |
implemented by Intel® 82546EB LAN Controller
via 64-bit PCI bus |
| |
two channels supporting 10Base-T, 100Base-TX,1000Base-T:-support
for PICMG 2.16 R1.0 — Packet Switching Backplane (PSB) |
| |
optional support for rear panel RJ45’s
via Transition Module |
| |
one channel switchable to front panel RJ45,
supports 10Base-T, 100Base-Tx and 1000Base-T |
| Graphics Interface |
implemented by a Silicon Motion SM722 providing:-8
Mbytes video memory resolutions up to 1280 x 1024; supporting
up to 16M colors accessed via a 26-way high-density connector
on front panel |
| PMC (PCI Mezzanine Card) Interface |
2 x PMC sites; |
| |
for both sites:- |
| |
-I/O via front panel |
| |
I/O via J3 and J5 |
| |
32/64-bit, 33/66 MHz PCI operation |
| |
3.3V or 5V signaling levels |
| |
Transition Module provides rear I/O for both
PMC sites |
| Serial Interface |
up to 3 x RS232 serial channels:-1 channel
via a 26-way high-density connector on front panel either
1 channel via J5 or 2 channels via optional Transition Module
16550 compatible UART channels support RI, CTS, RTS, DSR,
DTR and DCD |
| Flash Eprom |
32 Mbytes of Application Flash EPROM — 8-bits
wide |
| |
512 Kbytes of BIOS Flash EPROM — 8-bits wide |
| Battery Backed SRAM |
512 Kbytes battery backed SRAM |
| Software Support |
support for VxWorks®, Windows® NT,
Windows® 2000, Windows® XP, Windows® XP Embedded,
QNX®, Solaris® and Linux® |
| Other Peripheral Interfaces |
keyboard and mouse interfaces accessed via
a 26-way high-density connector on front panel |
| |
PC-compatible Real Time Clock (Year 2000 compliant) |
| |
watchdog timer system fan monitor; CPU temperature
monitor; voltages monitor:-all accessible via IPMI |
| |
speaker interface |
| |
1 x USB (Universal Serial Bus) interface via
J5 Transition Module |
| |
1 x 32-bit Long Duration Timer with processor
interrupt capability |
| |
LPC (Low Pin Count) bus via J5 to enable the
AD PP5/001 Transition Module support for: |
| |
-floppy disk interface |
| |
parallel printer port interface (ECP, EPP
and IEEE1284) |
| |
2 x RS232 serial channels |
| Firmware Support |
Phoenix ServerBIOS™ |
| |
comprehensive Power-On Self-Test (POST) |
| |
LAN boot firmware included |
| |
COMPACTPCI INTERFACE:|compliant with PICMG
2.0 R3.0; 3.3V or 5V signaling levels:-universal signaling
support |
| |
33/66 MHz; 32/64-bit interface accessed via
J1/J2 connectors |
| |
PCI-PCI bridge for off-board accesses |
| |
PICMG 2.1 R2.0 Hot Swap Specification compatible;
operates as a System Slot controller or in a Peripheral slot;
option to disable CompactPCI interface (Satellite Mode);
receives power from CompactPCI bus; board can be hot swapped;
J4 connector not fitted |
| IPMI (Intelligent Platform Management
Interface) |
PICMG 2.9 R1.0 (System Management Specification)
implements the IPMB0 interface on-board BMC (Baseboard Management
Controller) supports 8 Kbytes of non-volatile memory |
| Electrical Specification |
+5V@3.9A (typical at 1.8 GHz with 512 Mbytes
DRAM); +5% / -3% |
| |
+3.3V@6.5A; +5% / -3% |
| |
+12V@0.01A; -12V@0.01A |
| |
+12V and -12V routed to PMC slots |
| Safety |
PCB (PWB) manufactured with flammability rating
of 94V-0 |
| Environmental Specification |
operating temperature:-0°C to +55°C
(N-Series) |
| |
10% to 90% Relative Humidity, non-condensing
(operating) -40°C to +70°C (storage) |
| |
10% to 90% Relative Humidity, non-condensing
(storage) |
| Mechanical Specification |
6U form-factor: 9.2inches x 6.3inches (233mm
x 160mm) |
| |
single-slot: 0.8inches (20.3mm) |
| |
connectors: IEC-1076-4-101 for J1-J5 |
| |
shock:20g, 11ms, ½ sine (operating);30g,
11ms, ½ sine (non-operating) |
| |
vibration:5Hz-2000Hz at 2g, 0.38mm peak displacement
(operating) 5Hz-2000Hz at 5g, 0.76mm peak displacement (non-operating) |
