Pentium M

Pentium M 1.8GHz system/peripheral CPU board, 4HP, two PMC sites, with 512MB, 1GB, 1.5GB, and 2.0GB soldered DRAM (XX = DRAM).

Form Factor: 6U
Part Number: OSS-CPCI-6U-CPU-C-PM-1.8-2E-512

Product Features

• Intel® 1.8 GHz Pentium® M processor with 400 MHz Front Side Bus (FSB)
• supports up to 2 Gbytes DDR ECC SDRAM via two SODIMM sockets
• Dual Gigabit Ethernet
• Two PMC sites
• Support for VxWorks®, Windows® NT, Windows® 2000, Windows® XP, Windows® XP Embedded, QNX®, Solaris®

• 1.8 GHz Intel® Pentium® M processor 745:-400 MHz Front Side Bus (FSB)
• Common processor features are:-uses µFC-PGA 478 (micro Flip-Chip Pin Grid Array) package 64 Kbytes of primary (L1) on-die cache 2 Mbytes of secondary (L2) on-die cache no CPU fan

• EIDE interface:-supports up to Ultra-DMA 100 for high performance drives
• two channels (primary and secondary)
• secondary channel can be used for on-board 2.5 inch hard disk drive (within a single slot); or, support for 1 or 2 CompactFlash modules or Hitachi GST Microdrive™ Type II drives
• primary channel is accessible via Transition Module

• implemented by Intel® 82546EB LAN Controller via 64-bit PCI bus
• two channels supporting 10Base-T, 100Base-TX,1000Base-T:-support for PICMG 2.16 R1.0 — Packet Switching Backplane (PSB)
• optional support for rear panel RJ45’s via Transition Module
• one channel switchable to front panel RJ45, supports 10Base-T, 100Base-Tx and 1000Base-T

2 x PMC sites;

for both sites:-

• -I/O via front panel
• I/O via J3 and J5
• 32/64-bit, 33/66 MHz PCI operation
• 3.3V or 5V signaling levels
• Transition Module provides rear I/O for both PMC sites
  

• 32 Mbytes of Application Flash EPROM — 8-bits wide
• 512 Kbytes of BIOS Flash EPROM — 8-bits wide

• Keyboard and mouse interfaces accessed via a 26-way high-density connector on front panel
• PC-compatible Real Time Clock (Year 2000 compliant)
• watchdog timer system fan monitor; CPU temperature monitor; voltages monitor:-all accessible via IPMI
• speaker interface
• 1 x USB (Universal Serial Bus) interface via J5 Transition Module
• 1 x 32-bit Long Duration Timer with processor interrupt capability

LPC (Low Pin Count) bus via J5 to enable the AD PP5/001 Transition Module support for:

• floppy disk interface
• parallel printer port interface (ECP, EPP and IEEE1284)
• 2 x RS232 serial channels

• Phoenix ServerBIOS™
• comprehensive Power-On Self-Test (POST)
• LAN boot firmware included

COMPACTPCI INTERFACE: compliant with PICMG 2.0 R3.0; 3.3V or 5V signaling levels: universal signaling support

• 33/66 MHz; 32/64-bit interface accessed via J1/J2 connectors
• PCI-PCI bridge for off-board accesses
• PICMG 2.1 R2.0 Hot Swap Specification compatible; operates as a System Slot controller or in a Peripheral slot; option to disable CompactPCI interface (Satellite Mode); receives power from CompactPCI bus; board can be hot swapped; J4 connector not fitted

• +5V@3.9A (typical at 1.8 GHz with 512 Mbytes DRAM); +5% / -3%
• +3.3V@6.5A; +5% / -3%
• +12V@0.01A; -12V@0.01A
• +12V and -12V routed to PMC slots

• operating temperature:-0°C to +55°C (N-Series)
• 10% to 90% Relative Humidity, non-condensing (operating) -40°C to +70°C (storage)
• 10% to 90% Relative Humidity, non-condensing (storage)

• 6U form-factor: 9.2inches x 6.3inches (233mm x 160mm)
• single-slot: 0.8inches (20.3mm)
• connectors: IEC-1076-4-101 for J1-J5
• shock: 20g, 11ms, ½ sine (operating);30g, 11ms, ½ sine (non-operating)
• vibration: 5Hz-2000Hz at 2g, 0.38mm peak displacement (operating) 5Hz-2000Hz at 5g, 0.76mm peak displacement (non-operating)