| Backplane
Specifications: |
|
| |
One 2 link
system slot as defined in PICMG EXP.0 with rear I/O |
| |
One x16 type 1 peripheral
slot as defined in PICMG EXP.0 with rear I/O |
| |
Two x4
type 1 peripheral slots as defined in PICMG EXP.0 with rear
I/O |
| |
Three x4 type 2 peripheral
slots as defined in PICMG EXP.0 with rear I/O |
| |
One switch
slot as defined in PICMG EXP.0 |
| |
One Hybrid Bridge Board slot
to allow bridging the CPCIe backplane segment to the legacy
backplane segment |
| |
Four 32-bit/33MHz
legacy slots as defined in PICMG 2.x |
| |
These slots support rear
I/O |
| |
Connections
to at least 1 SATA or 1 SAS hard disk drive in front removable
canisters right of the system slot. |
| |
Connection to at least one
USB laptop style thin floppy disk drive right of the system
slot |
| |
Connections
to at least two PICMG 2.11 3U compatible power supplies. |
| |
The backplane supports as
many power and signal headers and traces possible to reduce
the number and/or length of cables inside the chassis. |
| |
All slots
in the backplane supports hot-swap. |
Hybrid Bridge board (HYB)
Specifications
|
|
| Form Factor: |
3U or 6U CompactPCI Express, PICMG EXP.0, Single Slot |
| Slot Type: |
PICMG EXP.0 bussed hybrid slot |
| Bridge: |
PLX PEX 8114 |
| Backplane Interfaces: |
One x4 PCI Express link on Advanced Differential Fabric (ADF) connector XJ3. |
| |
One 32-Bit/33 or 66 MHz PCI bus on HM connector J1 & power/additional PCI signals |
| Front Panel Indicators: |
Bank of 4 PCIe lane active indicators (green) |
| Power consumption: |
3.3V @ 2A |
| Temperature Range: |
0° to 55°C (32° to 122°F) |
| Switch board (SW) Specifications |
|
| Form Factor: |
3U CompactPCI Express, PICMG EXP.0, single slot |
| Slot Type |
PICMG EXP.0 switch slot |
| Power Consumption: |
3.3V @ 2A |
| Front Panel Indicators: |
Bank of 8 PCIe link-active indicators (green) |
| Temperature Range: |
0° to 55°C (32° to 122°F) |
| Power Supply Specifications |
|
| AC Input: |
90-264 Vac continuous
range, 47 to 63 Hz |
| Cooling: |
15 cfm, 225 lfm airflow
required for cooling |
| Thermal Protection: |
Shuts down power supply
if overheated |
| |
Automatic recovery |
| Temperature
Range: |
0 to 40
degrees centigrade at full ratings |
| |
derate 2.5% per degree centigrade
from 40 degrees to 70 degrees centigrade |
| |
unit will
start up at -20 degrees centigrade |
| MTBF: |
421,408 hours |
| Safety
Agency Approvals: |
Models
are approved to UL1950; CSA 22.2 #234 |
| Mechanical Dimensions: |
3U x 8HP W, 160 mm board
depth |
| |
Utilizes
a 47-pin modular connector in accorgance with PICMG Power
Interface Specification 2.11 |
